Description

Will continue with Ram upgrade as soon as the 3 main suppliers have been sued for price fixing and i can buy my 8 GB RAM stick for 40-50 bucks again

Comments

  • 18 months ago
  • 2 points

Just wondering what pushed your decision to go for an SFX power supply and not with a standard one despite the Meshify being able to support those.

  • 18 months ago
  • 1 point

Hi, I had an Asrock M8 series case before that was ITX. Same goes with the mini 1080. And since the power supply is no louder than a lower power ATX one i have i just used that one with its bracket. its as quiet as the case fans on low speed

  • 18 months ago
  • 1 point

I see. Well I guess that makes sense. Just a bit odd I guess, but to each and their own.

  • 18 months ago
  • 1 point

You do realize there are custom parts right? (You can add pretty much anything to your parts list even if it isn't on PCPP.)

  • 18 months ago
  • 1 point

Thanks! I didn`t know that

  • 18 months ago
  • 1 point

I am considering using the same case and it looks like the case has support for 3 120mm fans in the front but no support for a 360mm radiator. Do you know why this would be? I can not find a clear picture to see what would prevent this. Any input is appreciated, thank you.

  • 18 months ago
  • 1 point

Ive had a look and on first glance it doesnt really look like theres anything in the way of a 360. since its not alot wider than the fans. Looking at the manual though it looks pretty tight. Maybe its just that top part with the fittings that wont fit. Aslong as your not going I9, youll be good with a 280. And if you are, you may aswell go custom loop with dual 280s

  • 17 months ago
  • 1 point

does the RAM sync with anything?

  • 17 months ago
  • 1 point

Mobo softwares mainly. Nothing for me because the aio and the fans have own controllers. And since the ram is very bright i turn it down slightly to adjust to the aio.

  • 14 months ago
  • 1 point

Hey, wonderful build! Thinking about building basically the same things, was wonderings what you think of the combo of the mortar mobo and 8600k? Any heatproblems? :) Have the case already, just looking around for a competent matx mobo for the 8600k,

cheers!

  • 13 months ago
  • 1 point

Thank you! So far everything is running great. I have no comparison board but 5ghz was no problem. 5.1 just gets too hot on the chip. The VRM on one of the asus matx would probably be better but for an i5 this is fine. Keep in mind that the RGB controller is limited to 7 colours and nearly no effects. No rainbow if you're into that.

[comment deleted]
  • 13 months ago
  • 1 point

The cooler and the fans are great. My current fan setup runs at 900 rpm constant. 5 ghz with 1.345~vcore. Liquid temperature goes from 27 to 47 depending on ambient(which is about 25ish) So far below permiation point. Pumpspeeds don't matter at all it seems to me. And the original fans never really need to run over 40%. Installation is also pretty straight forward. Top exhaust fans will be in the way of the tubes depending on how you mount the rad. Stock thermal paste also performed pretty good.

[comment deleted by staff]
  • 18 months ago
  • 1 point

For now, will post more with more mods. corsair LL coming

  • 16 months ago
  • 1 point

Looks good! Have you gotten the corsair LL fans yet? I'm looking at these fans myself in this exact case. I don't have any RGB strips and the dark tint makes it difficult to see anything other than glowing Mobo lol But I like it so far

  • 16 months ago
  • 1 point

Hello. I was about to get the LL series fans but didnt feel like paying for 6 of them so i went with enermax fans. As you said, the glass is very dimm and doesnt show much else than the LEDs themselfs. I dont really know a lot about the LL fans alot but they should spill more light in your case than the enermax fans will. I for example also took one rgb strip in the front and top to give all components some light since its just so dark

  • 16 months ago
  • 1 point

If I went and replaced the meshify mini c with the regular meshify c, do you think the non tint glass looks better OR do you like the dark tint? I realized I can get a full ATX mobo in the Meshify C since there are no X470 chipsets available in the Micro atx size. The case dimensions are exactly the same except for the physical height. I think it's roughly 1.75inches taller

  • 16 months ago
  • 1 point

I personally like the dark tint more. But it depends. Maybe you want to see everything if you have a very nice motherboard and cable management. It depends on how you highlight stuff. I had a small form factor gpu that i didnt want to swap. Its not that visible with the tint but looks stupid in a clear case.

Its all pretty much the same. The front lit up with 3 fans is quite satisfactory with its mesh. The LL fans will give that pattern even more character